Johny

Bigger the better.

I run an eheim 2260 on my 6x2x2 and it keeps my water crystal clear. They fit the most amount of media than any other cannister on the market.

Pricey but if you were to run a single cannister on that size tank this would be my pick.

With the eheim classic there is no auto prime either but surprisingly primes so easily.
Update - tank is now filled and been running for the last few days with water. Of course of all things I forgot to get was an air stone so still need to sort that out haha.

Here is how she is currently looking with rocks and driftwood in - 

Close up of the Garnet - 

Wish I could at this stage haha she should sell soon though its a steal! Then you can consider giving up those birchirs 

Okay so since last post I tracked down a proper hanging kit and got the light sitting to where it should be.

What also finally arrived today was the new Eheim, here is a photo of the big girl.

Also ordered the quick release taps to go with it.

Over the last few weeks I was already accumulating the filter media so it would be ready to go in once the eheim arrived.

Here is all that I ended up purchasing. All in all I used most of it bar the seachem matrix as I did not have enough room to fit that in. Will keep it as spare bio media or move it on perhaps depending how the other stuff does the Job.

Ill do a step by step guide as to how I stacked the filter.

First layer of Mechanical filtration I used 5 litres of Eheim EfiMech

Second stage of mechanical filtration was Poret foam that I ordered in from Swisstropicals over in the US after hearing Rave reviews online about it.
They were easy to deal with and shipping was cheap so couldn't complain.

Ordered one sheet of 10PPI 2inch and one sheet of 20PPI 1.5inch.

Cut it to suit the cannister.

Then to top the mechanical side off I just added in some cheap filter wool.

Now moving on to the Biomedia this is where I originally wanted to run both matrix and substrat pro. Of course prior I didn't know how much of each I could fit so after adding all the mechanical side in I was not left with much room so opted to do just the full 5 litres of Eheim SubstratPro and leave out the seachem.

After the biomedia I cut the PolyFilter pad to suit the cannister as the final layer of filtration followed by two bags of Seachem Purigen for extra water clarity.

Lid then went on and I finished fitting of the pump to the lid of the filter (All comes disassembled for those wondering)

Afterwards finished fitting of the cap, attaching the inlet and outlet hose along with the quick disconnect taps.

Overall a timely and costly exercise opting for this filter but for the purposes, functionality, performance and reliability I intend to use it for I couldn't look past it.

Extremely happy with the flexibility to stack the filter exactly how you want it and getting the best of both worlds with mechanical and bio filtration. The sheer amount of media you can fit in is astonishing.

Moving on I now am pretty much ready to fill the tank with water, connect everything up and start the cycle! Snowed under the next few days but hopefully by end of week she will be there.

The plan will always be to keep whatever tb's and exotics I can get my hands on! 

Quick update - 

This was the end product of the stand once all sanded down and varnished.

Did some shopping over the last couple weekends and managed to pick up the heater and light as well. Big thanks to Morley aquariums and City barn malaga for providing the goods!

Opted for a NemoLight 72w and a titan G2 Heavy duty 600w heater.

Now for the lighting I remember it was always such a pain taking it off and on again during the water changes and generally just getting in the way of things when it was time for water changes so I did not want a repeat of that.

Decided I was going to run a smaller light and have it suspended over the tank.

Reason for the smaller light was also because I do not want excessive lighting. I like the more ''natural'' look in a tank and if I can have the two sides a tad bit darker then that would be ideal.

So after 2 weeks from ordering, my custom light stand brackets finally showed up yesterday.

Wasted no time in getting them installed to the back of the stand.

Finally it was time I could move the tank to inside the house and on to its stand.

Here is a quick photo with the suspended light hanging from it.

Still need to play around with the height of the light as I want to bring it down a bit lower now that I have seen it lit up but Ill worry about that later.

Additional extras I have purchased that are arriving and due on its way is the Fluval Air pump, Various water conditioners and test kits and filter media. Forgot How quickly it all adds up starting from scratch again haha.

Next pay I plan on ordering the cannister. Deciding to go for the Eheim 2260. Figured for the sheer size of media it can hold there is no equivalent on the market! Just costs an arm and a leg when you factor the additional quick disconnect taps and all the filter media but as they say do it once and do it right 

Looking good mate!

Well for those who were around back then and may remember I kept quite the collection of tank busters for a pre-adolescent teenage kid haha some of them including Aros, bichirs, rtc, clown knives etc etc.

Unfortunately all good things came to an end after I lost some of my prized fish and so I decided to sell what was remaining and move on from the hobby for a little while.

I didn't think it would take so long but life had kept me at bay to get back into it sooner but finally after 8 or so years I bit the bullet and purchased a new tank.
A brand new 6x2x2 with a pine stand came up for sale and I managed to score it for $600. Freshly built by Morley Aquariums it hasn't even be filled yet! Has the back painted black and black silicone around all the edges. Couldn’t ask for more. 

The plan was always to have it in my room so the lack of cabinet / hood does not worry me.

I’ll start with a quick photo of the stand after I took delivery.

I was not too happy with the overall strengthening of the stand. There was excessive movement when pushed from each end.
Went past the local Bunnings and purchased 5 metres of pine timber and cut it down to size and braced the entire bottom of the stand.

As shown I went both horizontally and vertically between each main leg. Finished it off with a thin piece of ply board over the top where the tank will eventually sit on with foam as well.

Here is the end product.

Made a huge difference. Now there is no longer any movement either way and I am finally feeling confident with it.

Tonight I will sand it down and apply the first coat of varnish to it.

Will keep this post updated as I go along.