Outdoor Fish Tank
#1
Posted 23 February 2016 - 11:06 PM
Just wondering if anyone keeps relatively large (6ft +) fish tanks outdoors? What are the heating costs like in winter and is it worth it?
#2
Posted 24 February 2016 - 07:02 AM
1600ltr tank was way too hard/expensive to heat.
How warm do you want to keep it?
#3
Posted 24 February 2016 - 10:22 AM
LOL
i was just thinking about this last night.
i have tank rack outside and wanna keep it around the 20C mark for the guppies.
i'm thinking styrofoam around the sides, back and lids
ugly as heck but if it will save me money in terms of heating then i dont mind
#4
Posted 24 February 2016 - 12:09 PM
We have a rack out side as well had it there for coming on 2 years and no issues whatsoever 31c was the hottest during the recent heat wave
We used to use styrafoam on each tank but middle of last year we changed to the sheeting they use in house construction between walls an in the roof space it is soft and pliable and looks better than styrafoam
also it does both stops heater coming on too often during winter and also will stop the heat as well to a certain degree
- changy likes this
#5
Posted 24 February 2016 - 01:27 PM
i have no problem with hot days as they are sitting under the patio
more for when it gets cold..
i googled a bit and someone suggested this :
http://www.bunnings....oofing_p1010565
i was thinking of attaching to back and sides of the rack, and have it held on temporarily on the front for night time?
We have a rack out side as well had it there for coming on 2 years and no issues whatsoever 31c was the hottest during the recent heat wave
We used to use styrafoam on each tank but middle of last year we changed to the sheeting they use in house construction between walls an in the roof space it is soft and pliable and looks better than styrafoam
also it does both stops heater coming on too often during winter and also will stop the heat as well to a certain degree
http://www.bunnings....-board_p0811027
something like this?
#6
Posted 24 February 2016 - 04:12 PM
I've seen little Dickies and i'd have to say he did a rather good job. I don't think it is an eye sore at all it's thin as cardboard. silver on the outer 2 side with a sponge centre i think from memory. Worth giving it a go i'd say but i'm sure he can describe it better how he went about it and cost plus you have the benefit of his 2 years of using it.
#7
Posted 24 February 2016 - 07:23 PM
sorry cant remember the exact name will find out tho , was free from Eileens son in law got about 1/2 roll it did 8 tanks it is silver on both sides but they have different patterns so what ever makes ya happy on the outside ... it is rubbery type filling in middle and it is fire proof also extremely flexible ... watch tis space for the name of it
#8
Posted 24 February 2016 - 11:41 PM
- malawiman85, changy and shayne like this
#9
Posted 25 February 2016 - 12:07 AM
Yes, I paid a huge price for my pleasure on the patio last year. Unfortunately my favourites are going in the shed this year, i will be left with goldies,tandanus and going to risk a cod. Will keep some heaters handy in case we get a real cold snap. You might find one insulated tank affordable, don't know your budget, i foolishly did 2 6x18's and a 4x2 and my shed, bills reached 800$ plus a couple of times had to tell my partner they were my responsibility and she wasn't allowed to open them.
#10
Posted 25 February 2016 - 02:37 AM
Was it called "heat block",,,,sorry cant remember the exact name will find out tho , was free from Eileens son in law got about 1/2 roll it did 8 tanks it is silver on both sides but they have different patterns so what ever makes ya happy on the outside ... it is rubbery type filling in middle and it is fire proof also extremely flexible ... watch tis space for the name of it
20mm sheet polystyrene as already mentioned works well,,, you can join corners with water based liquid nails.
You can also use 50mm chipboard screws to fasten corners while the glue drys.
A black water based paint or any color choice can be used to blend into its area.
Getting creative......... Bunnings sells Velcro strips and squares with a super strong adhesive backing,, you could use this for the front face edges to hold front panel in place during day/night and super easy to remove and replace.
The fact that polystyrene is rigid, it makes it very easy to install and gives a cabinet like straight edge neat finish.
A cheap long blade Stanley knife and straight edge will make easy cutting.
- malawiman85, changy and chocky like this
#11
Posted 25 February 2016 - 12:51 PM
#13
Posted 26 February 2016 - 02:32 AM
But line the inside of the gyprock with heat block and your cooking with gas.
But using gyprock is a poor option, not only for insulation, but for construction and assembly wise, better of using plywood with a insulative internal lining.
If one wanted to get creative, again, construct from polystyrene 30mm as noted above,,, and paint with a dulux product called Acra-Tex.
Use a paint roller called a loop roller, it has little loops in the roller fabric designed to pick up and pull little nipples all over the thick paint finish,,, and it will perfectify the entire surface of polystyrene to a uniform look.
Even more creative again, is to glue and cover polystyrene with any type of fabric material, or even thin aluminium sheeting can be glued for a finished surface, or even laminex.
#14
Posted 27 February 2016 - 10:38 AM
hey all finally got the name of the stuff I have used to wrap the tanks in outside
Polyair Forma R4.0
Available from BGC supply in Canningvale probably other builders supply places as well
#15
Posted 27 February 2016 - 03:39 PM
#16
Posted 29 February 2016 - 06:09 AM
Tank will need to stay around 26-27C. So you guys reckon just keep the three sides really well insulated and I shouldn't rack up a massive electricity bill?
#17
Posted 29 February 2016 - 07:21 AM
300 watts (I suppose thats what you have in mind to heat this tank at least) per hour on most of the time. Power is charged in kilowatt (1000 watts) units so every 3 and a bit hours the heater is on you get charged an additional unit on your bill.
Edited by malawiman85, 29 February 2016 - 07:22 AM.
#18
Posted 29 February 2016 - 07:29 AM
#19
Posted 29 February 2016 - 09:22 AM
if you insulate correctly, you can make it even more economic than a tank sitting inside a house.Tank will need to stay around 26-27C. So you guys reckon just keep the three sides really well insulated and I shouldn't rack up a massive electricity bill?
Buy yourself a brand new sheet of 30mm, 20mm is ok but 30mm easier to construct and better insulative.
Completely all round encase your tank with a removable front face so you can remove to view.
It's like sticking your tank in a esky,,, EXTREMELY effective.
Some people choose materials based on what they can afford or limited skills in engineering/construction.
Once you have the foam in place, your tank will be the most economical it's ever been, mid winter or at any time,,, (no gaps no voids).
- changy likes this
#20
Posted 29 February 2016 - 09:26 AM
What Buccal has said do all the sides of the tank including the top of the tank .... I have used Velcro to hold the front and top on
0 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users