Jump to content





PCS & Stuart M. Grant - Cichlid Preservation Fund - Details here

PCS Photo Competition 2017 - Enter Now - Details here

November PCS Meeting  - Movie Night Tues 7th November - Details here

November Fish of the Month - Tropheus sp. duboisi - Details here

December Fish of the Month - Neolamprologus brevis "Sunspot" - Details here

PCS Family BBQ Fun Day 2018 - January 14th - Details here


Photo

Eheim 2080 Intake Mod


  • Please log in to reply
8 replies to this topic

#1 Mintox

Mintox
  • Forum Member
  • Joined: 24-February 05
  • Location: Alexander Heights

Posted 08 October 2017 - 10:34 AM

H guys,

 

I have two of these running on my 5x2x2. The tank is overstocked and I find the 2080's do a poor job of mechanically filtering the water. I put this down to their small intakes, I find the larger pieces of waste just float right by. I was considering converting the two intakes into one 25/34mm intake which would then split back into the two 16/22mm intakes feeding the filter. Has anyone come across this or think this is a silly idea?

 

Alternatively I was thinking of swapping out one of the 2080's with an Fx6 or converting to a sump. If I was to down the route of a sump, is drilling the tank whilst it is running not possible too risky?

 

Cheers,

 

Peter 



#2 humbug

humbug
  • Forum Member
  • Joined: 26-December 12
  • Location: Adelaide, South Australia

Posted 10 October 2017 - 02:44 PM

I've used both the FX6 and the 2080, and I suggest that if you swapped to the FX6 you would be very disappointed! 

How have you got the Eheims set up?  What media are you running, and are you using the Eheim white and blue filter pads? 


Edited by humbug, 10 October 2017 - 02:45 PM.


#3 Peckoltia

Peckoltia
  • Forum Member
  • Joined: 15-October 04
  • Location: Dianella

Posted 11 October 2017 - 03:31 PM

If converting to a sump is an option you can and are willing to take, then go for it. Cannot compare a properly set up sump to a canister filter, they are worlds apart.



#4 Cawdor

Cawdor
  • Admin
  • Joined: 26-December 05
  • Location: Byford

Posted 16 October 2017 - 06:30 PM

I have combined the two intakes into one 25mm pipe intake. Works well, I need to clean the top coarse filter pad once a month (medium stocked 8x3x3).



#5 Ageofaquariums

Ageofaquariums
  • Forum Member
  • Joined: 24-January 04
  • Location: Browns Plains. Qld

Posted 18 October 2017 - 06:34 AM

Adding a powerhead style filter that specializes in mechanical filtration beside the canister intake would also improve ability to capture particles.



#6 Mintox

Mintox
  • Forum Member
  • Joined: 24-February 05
  • Location: Alexander Heights

Posted 19 October 2017 - 08:01 PM

Thanks for the replies guys.

 

I've used both the FX6 and the 2080, and I suggest that if you swapped to the FX6 you would be very disappointed! 

How have you got the Eheims set up?  What media are you running, and are you using the Eheim white and blue filter pads? 

 

I have all the default media installed with my Eheims including the white and blue pads. Regardless of how often I change the white pad, it doesn't make a difference. Can confirm great flow from both.

 

If converting to a sump is an option you can and are willing to take, then go for it. Cannot compare a properly set up sump to a canister filter, they are worlds apart.

 

I wish I had gone down this route to begin with. I purchased a second 2080 to handle the bio load quite a few months ago and could have invested in a DIY sump. Might try setup a smaller tank with a small sump to get the hang of it.

 

I have combined the two intakes into one 25mm pipe intake. Works well, I need to clean the top coarse filter pad once a month (medium stocked 8x3x3).

 

Do you mind sharing your details or parts on how you did this? I had a quick look down at a Total Eden and couldn't find anything promising.

 

Adding a powerhead style filter that specializes in mechanical filtration beside the canister intake would also improve ability to capture particles.

 

Do you have any quality power heads and sponge setups you would recommend? I have previously had some Ottos and find they can be a bit noisy after a while.

 

Cheers,

 

Peter



#7 Ageofaquariums

Ageofaquariums
  • Forum Member
  • Joined: 24-January 04
  • Location: Browns Plains. Qld

Posted 20 October 2017 - 07:24 AM

Honestly if you could spare $200 or so, an aquael reef circulator 10000 would be my suggestion. 20 watts of silent oxygenation and particle suspension. Combined with good placement of canister intake/outlets, you could get complete water movement that never lets debris rest and instead delivers it to canister intakes + total surface area agitation. Yea its a bit of an investment, but its quality and minimal aesthetic impact.

 

On the other hand the petworx 2300 internal is shaping up to be a good work horse. Cheap, not too bad on sound and black so tends to blend into background. Can also capture/hold a lot of debris between cleans.


Edited by Ageofaquariums, 20 October 2017 - 07:24 AM.


#8 Cawdor

Cawdor
  • Admin
  • Joined: 26-December 05
  • Location: Byford

Posted 20 October 2017 - 07:12 PM

Hi Peter,

 

This is how I did it:

Attached File  20171020_190348.jpg   73.51KB   1 downloads

Attached File  20171020_190400.jpg   78.59KB   1 downloads



#9 Mintox

Mintox
  • Forum Member
  • Joined: 24-February 05
  • Location: Alexander Heights

Posted Yesterday, 08:16 PM

Honestly if you could spare $200 or so, an aquael reef circulator 10000 would be my suggestion. 20 watts of silent oxygenation and particle suspension. Combined with good placement of canister intake/outlets, you could get complete water movement that never lets debris rest and instead delivers it to canister intakes + total surface area agitation. Yea its a bit of an investment, but its quality and minimal aesthetic impact.

 

On the other hand the petworx 2300 internal is shaping up to be a good work horse. Cheap, not too bad on sound and black so tends to blend into background. Can also capture/hold a lot of debris between cleans.

 

Thanks mate. Already dropped quite a bit on a high end wave maker from you guys. May attempt the intake mod and see how things progress.

 

Hi Peter,

 

This is how I did it:

attachicon.gif20171020_190348.jpg

attachicon.gif20171020_190400.jpg

 

Thanks Tim. That's a lot of plumbing! Has given me some food for thought, thanks again.






1 user(s) are reading this topic

0 members, 1 guests, 0 anonymous users