Dazza's Shed
#1
Posted 21 March 2009 - 11:01 PM
Began assembling my 6M x 3M x 2.1M shed today. Pretty happy with my efforts so far as I consider myself not to have a "handy" bone in my body LOL. Managed to get this done on my own with a couple of minor mistakes along the way.
The location. Already has bitumen down which is a bonus!
Some of the bits n pieces.
Rear wall assembled (laying on ground).
All walls up. Roof will be done tomorrow hopefully.
Any tips/feedback appreciated. One thing I am concerned about is the flooring. Whether or not I should lay something over the bitumen inside the shed. Firstly I want to prevent any unnecessary temperature transfer that will be passed via the floor from the outside. Secondly worried about water entering the shed via the floor on rainy days.
Dazza
#2
Posted 21 March 2009 - 11:39 PM
If the bitumen slopes towards the shed, then I would just silastic on that side. Where the bitumen slopes away from the shed I wouldn't bother, as this will help any spillages etc drain away.
I doubt if you would get much heat transfer from the outside to inside the shed.
Hope this helps.
What do you mean you will put the roof on tomorrow....don't you have any outdoor lights...or a torch ?
You're getting slack Dazza.
Col
#3
Posted 22 March 2009 - 12:11 AM
Dazza
Hi Dazza,
There's not much you can do about it at this stage, but you will lose significant heat via the bitumen floor. As Col suggests, I think it would help to seal the shed to the bitumen, but I would do it all around the base of the shed to prevent draughts at least. You will need to drill some holes in the floor for drainage of spills etc.
The best sealant would be a silastic formulated for masonry (non-acid cure).
Syd.
#4
Posted 22 March 2009 - 08:34 AM
You're getting slack Dazza.
I'm not saying it didn't cross my mind to continue on last night but I don't think the neighbours would've appreciated it
Thanks Col & Syd for the info so far. Regarding drilling a drain do you mean downpipe/soakwell style or just a few wholes leading outside the shed??? (keeping in mind using a drill is as 'handy' as I get )
Daz
#5
Posted 22 March 2009 - 04:15 PM
If not I would recommend you knock on the neighbours door and make sure they dont have a problem with it, cos if they do complain you will be pulling it down... stupid neighbours!
How are you getting power to the shed. It might have been nice to run a conduit under the ground before you put the walls up if you dont want the main power cable visible.
Looks like a good job so far... feel free to come help with mine when you are finished!
Andrew
#6
Posted 22 March 2009 - 04:55 PM
Regarding the power to the shed, if you do dig a conduit in make sure it's the correct type and sufficient depth.
Otherwise it will be a waste of time because the sparky won't be able to use it.
I'm happy to give advice re the electrical, but unfortunately aren't able to do it for ya.
ado
#7
Posted 22 March 2009 - 06:03 PM
Neighbours should be okay with it. I approved the parapet wall they want to build on the fence line. Better go knock on their door to be on the safe side.
Power wise I was thinking of getting a line run from the house roof/eve down to the shed (about 3 or 4 metres)?? Jack hammering and digging a channel is way out of my league.
Daz
#8
Posted 23 March 2009 - 07:23 AM
Dazza, Re. above.
I have an electric 26kg demolition hammer drill ( jack-hammer) which would just sail through bitumen.
Col
#9
Posted 23 March 2009 - 07:42 AM
What sort of assistance do you need?
I might be able to pop around and give you a bit of a hand, but I'm only available during the day in the week.
Not sure if that suits you at all?
#10
Posted 23 March 2009 - 09:29 AM
Tony
#11
Posted 23 March 2009 - 04:47 PM
A bit of help with good old google might find you an online set of instructions.
I know structural steel, house sheds are not quite to my knowledge, unless you want to upgrade to 6mm+ thick steel and 150mm purlins, guaranteed to never ever ever fall down! But the cost factor may blow out a bit.
#12
Posted 23 March 2009 - 09:03 PM
It's a Spic 'n' Span shed ( http://www.youraussiemate.com.au ). Locally made AFAIK. I'll give them a buzz tomorrow to clarify the points that I'm stuck at.
Regarding jackhammering a drain, channel etc do you all think this is worthwhile? I was thinking more of a pump to suck the water out into a large tub/container and from there feed into the garden??
Daz
#13
Posted 29 March 2009 - 08:00 PM
A couple more updates.
Wall and roof supports are up as of yesterday.
Roof panels and doors are up as of today. Adding flashing, door handles etc will be the final step to building the shed.
The strength of the roof supports have me concerned so might look at reinforcing it further and perhaps even a centre support down to the ground.
The roof panels don't line up perfectly at the 2 ends of the shed so I'm assuming I haven't built it perfectly square. I'm now left with a gap of about an inch. Should I bother taking down the roof and realigning or just cover the gap with some flashing?
Next step is to test for leaks and start sealing. I assume I'll need to keep the internals as dry as possible if I'm adding an insulator of some sort?
Not bad having done most of it on my own hey!
Daz
#14
Posted 29 March 2009 - 08:29 PM
#15
Posted 29 March 2009 - 08:49 PM
bad luck with the gap, bet u can fix it though
gonna have alot of money worth of fish in there! hope u dont loose any!
cheers, paul
#16
Posted 30 March 2009 - 05:05 PM
Quick way to check if it is square.
I used to use it the check tilt panels againg surveyors points.
If it is out of square and isnt too hard to straighten, I would do it, but I can be a pedantic prick, thats what the guys working under me used to call me anyway.
If its too difficult... flashing is cheap!
They make it cheap on purpose, if you knew how off square some buildings are... flashing covers all!
Looks good tho.
How are you going to insulate it? are you going to have gyprock on the walls? If so what are you going to screw it to?
Andrew
#17
Posted 01 April 2009 - 09:37 PM
Please explain....
Insulation wise I'm thinking the foil roll stuff with the one furry side. Or the spray on stuff that Steve Green mentioned. Need to source who does it though....
Daz
#18
Posted 03 April 2009 - 05:32 PM
Doesnt have to be metres, can be feet, or can be 1.5m, 2m and 2.5m.
Hope this makes sense, if not I'll draw a pretty picture!
Andrew
#19
Posted 03 April 2009 - 06:03 PM
You can use any measurements if your shed is smaller than the values Andrew gave you.
#20
Posted 05 April 2009 - 08:50 AM
0 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users